12 V starter battery weak after 15 months

Wolfi

Ist öfter hier
Has anyone had issues with a weak battery in the Cupra Formentor e-Hybrid with a registration date of 03/2025?
The battery management system seems to be functioning. When the charging cable is connected, the voltage is 13.1 V. While driving, the 12 V battery is charged with 14 ... 15 V.
When the vehicle is then parked, the voltage drops to 12.3 V. Within 2 days, the voltage then decreases to 11.6 ... 11.4 V. When opening with the button on the remote key, the voltage then collapses to about 10.7 V. Opening via KeylessGo has already been deactivated. Sometimes, the configuration data needs to be reloaded according to the infotainment system.
I don't believe this is caused by a consumer with too high a standby current, as charging with a CTK charger indicates full after 2 ... 3 hours
What is your opinion? This should definitely still be covered under warranty for a 15-month-old vehicle, right? Are there any corresponding experiences?
 

Attachments

  • Screenshot_20260531_103305_Battery Check.jpg
    Screenshot_20260531_103305_Battery Check.jpg
    132.9 KB · Views: 4
  • Screenshot_20260531_090353_Battery Check.jpg
    Screenshot_20260531_090353_Battery Check.jpg
    131.2 KB · Views: 3
  • Screenshot_20260531_090339_Battery Check.jpg
    Screenshot_20260531_090339_Battery Check.jpg
    122.3 KB · Views: 4
  • Screenshot_20260531_103709_Battery Check.jpg
    Screenshot_20260531_103709_Battery Check.jpg
    113.9 KB · Views: 4
Should go under warranty and wouldn't be the first 12v to die prematurely. Go to the workshop, but it's better not to mention charging it yourself (according to the Manual*, you shouldn't charge hybrids yourself).
 
So in my Manual* it even states where the 12 V connection for charging is (in the fuse box). If I didn't do this every now and then, I wouldn't have been able to get in after just a few days, and they could have picked it up with a tow truck. An EFI battery can be charged without any concerns. Of course, one shouldn't charge it via the wall box or turn on the vehicle.
 
Check your operating Manual* for that. Here is just an excerpt from the section on the Terramar. Middle column "you should not charge yourself"...

Screenshot_20260621-175205.png
 
The Cupra specialist does not charge the battery any differently than a private individual would, provided they have the necessary knowledge. I have also charged the battery myself on my Cupra Leon PHEV and even replaced it with a new battery of the same type last August on my own. If you know what you're doing, you don't need a specialist workshop for that.
 
Last edited:
The Cupra specialist workshop does not charge the battery any differently than a private individual would, provided they have the necessary knowledge. I have also charged the battery myself on my Cupra Leon PHEV and even replaced it with a new battery of the same type last August on my own. If you know what you're doing, you don't need a specialist workshop for that.
Exactly, you must not activate the DC/DC converter. That means no charging cable should be plugged in and the ignition should be left off.
 
That's not the point at all. I pointed out to him not to mention that he charged it himself. Why? So that the workshop or SEAT can't wriggle out of it.
 
  • Like
Reactions: ekm
@Wolfi It's a well-known problem (welcome to the club), I've had my issue with it twice now, once there was apparently a bad batch of 12V batteries installed in the earlier PHEV models, mine was replaced and I had peace for a while. Then a few months later, the problem came back, this time the battery was perfectly fine, only a control unit(s) wasn't shutting down properly and drained the 12V battery....

Go and have it checked, it's a very well-known problem, I hope I finally find peace with it now. My Tipp, have them install the PV4 update directly, it might be that they also replace a few control units for you then 🤷‍♂️
 
So I had my Formentor in the workshop a few weeks ago due to the problem. It seems to actually be a known issue for which there is already a manufacturer information (TPI ?). The cause is the central gateway, which also supplies the OBD interface
 

Yes, TPI (Technical Product Information) is correct

If a TPI exists, that is very good! Because the manufacturer has dealt with the problem, let's say, they recognized it due to frequently similar error messages and wrote corresponding procedures for the workshops. Accordingly, there are good chances for rectification (within the scope of warranty/guarantee, if applicable).

If you should somehow become aware of the number of the TPI, we have a thread where the known TPIs are collected, see hierGlück Auf !
 
@Wolfi Did you receive the big update to 2768 because of that?
 
@Wolfi I also find that more than frustrating; I don't understand why they don't contact the customers and ask them to have this checked at a workshop.... Instead, they prefer to leave the customer stranded with a breakdown somewhere and then also pay for the towing costs, etc.....

Well, I'm just an amateur, but it looks different to me for the customer.
 

* = Advertisement
Links marked with an asterisk (*) are affiliate links. If you click on one of these links and make a purchase, we receive a commission from the respective online shop or provider. This does not affect the price you pay.

Back
Top