ABS, CCan Bus communication issues

frk197_

War schon mal da
Good evening, everyone.

Since November 2025, I’ve been the owner of a Cupra Leon with 300 PS.

For about the past month, I’ve noticed that my oil temperature gauge is behaving erratically. It jumps up and down by 20–30°C every second. From 50°C to 80°C, then back down to 50°C or 60°C. Now I thought I’d try reading the control units with Carly. My suspicion was on the oil temperature sensor.

After running the diagnostics, I was greeted with 43 faults xD. Visible in the images1000037498.jpg

Here is an example of ABS brakes:
1000037499.jpg

I unfortunately can't upload the complete Carly report as a file (at least not from my phone).

What I've done for troubleshooting:

Error codes deleted > re-read: again 43 errors > again deleted > driven for 20 minutes > full brake until ABS kicks > re-read > deleted > re-read again: again 43 errors.

Interestingly, no messages appear on the dashboard or screen.

Before I run to the next workshop, I wanted to ask online whether anyone else has had the same issue?

My guess:

• Cable break / chewed wire
• Fuse blown
• Control unit defective (which one ever?)
• Carly is giving nonsense

What does the community think?

PS: I'm just an amateur mechanic. When it comes to electronics, I'm no expert. Yes, I'll definitely have the issues resolved at a workshop, but before spending thousands of euros on diagnostics and repairs, I'd like to gather your tips and advice first.

Regards

Frk
 
Moin @frk197_ and welcome to the Forum!

Just some thoughts from me – I’m not a car expert either but I do know about IT systems... I have the feeling that this isn’t entirely out of place with today’s cars.

The oil temperature sensor is probably a simple NTC, so a semiconductor. Since it is exposed to strong temperature fluctuations in use, even the smallest manufacturing defects can cause such behaviour. So I would initially suspect a faulty sensor here. In many vehicles, it’s also the case that you don’t actually see the “real” sensor value on the dashboard, but rather the result of a stored characteristic map and additional logic. If you want to experiment, you can try using Carly while driving and observe the oil temperature live (Carly should have such a function, though I’m not familiar with it).

Regarding all the other messages you have, they don’t necessarily indicate actual problems. There are different types of messages (info, warning, error, etc.) that Carly might not classify correctly. For example, I see timeouts on your screenshots... in such complex networked systems, these are almost unavoidable, since real-time system efforts are usually only made for safety-relevant components. It would of course be interesting to know exactly what the errors are.

If everything else in the car is functioning normally and there are no warnings on the dashboard/multimedia system, I wouldn’t worry about the sheer number of messages for now.
 
When I had mine in the workshop for a logo change and subsequent sensor calibration, several messages were already stored after 3 weeks.
So this is nothing unusual; these so-called "Phantomfehler" or sporadic faults are completely normal in modern vehicles. Often, they are digital "cosmetic faults" recorded in the background without any mechanical defect.

Example:
- A control unit waits milliseconds too long for a response from another. The system logs a communication error (often U-codes), even though everything runs normally the next moment.
- If the onboard voltage briefly dips slightly when starting, sensitive sensors can deliver implausible values. These are stored as faults but do not affect driving.
- Some limit values in the software are set so tightly that minimal deviations (e.g. due to outside temperature) already trigger an entry.

Many modern control units automatically delete sporadic faults if they do not reoccur over a certain number of start cycles (often 40 or more).
As long as no warning light is on and the car drives normally, such entries usually do not cause concern or require costly repairs.
 
Hallo @Milan and thank you!

Yes, the temperature gauge was also my first thought, so regarding the sensor. Because I read exactly the same problem online in this forum and other sites. Many users had the same issue. Therefore, I will replace the sensor soon on a whim. Although I have a used car warranty, the dealership wants to perform a diagnosis first to process it... I think I'll leave that for now.

As for the errors, yes, it's unfortunately nothing new that cars today have a lot of electrical problems; it's rather normal. I also think that Carly might have been talking nonsense. However, I will have it read out with VCDS by an acquaintance.

Yes, there are no messages, ABS is working as well. I will keep an eye on it.

Thank you for your help!

Hello @danthemanThank you for your response and help.

Yes, that was also my thought, but when the errors kept coming back after deleting, I became a bit suspicious, even though everything works, drives, and brakes completely normally.

I will definitely keep an eye on it and write an update here if anything changes.

Thanks again.
 
Last edited by a moderator:

* = Advertisement
Links marked with an asterisk (*) are affiliate links. If you click on one of these links and make a purchase, we receive a commission from the respective online shop or provider. This does not affect the price you pay.

cupra.forum · Alle Rechte vorbehalten · Dies ist kein Forum der Seat Cupra S.A.U.
Back
Top