12 GB large update for Terramar control units

Hello everyone,

this coming Saturday I will receive my Terramar and I am diligently reading (almost) every post here. It's always nice to see how you help each other out.

After reading about all the problems following the updates, my conclusion would be to never start an update. Is it possible that the vehicles receive a mandatory update, or are there such significant jumps/extensions in new versions that you install the latest software despite the risk that something might not work afterwards?

Best regards, DeRoony
 
Your vehicle will already have the current software version, so THAT update is not problematic for you. As far as I understand, it is the case here that the installed hardware cannot always handle the new software. For some, changing individual control units has helped, while others are still looking for solutions. As long as there are no problems, there is no need to perform a software update. With a few exceptions, these are all updates that take place at the workshop. The small OTA updates are generally unproblematic and are updated automatically in the background.
 
And from my own experience, I can say that I haven't received the message with the onboard Manual* since last week; that seems to be under control now. So don't worry too much, you should be spared from most of the teething problems. ;)
 
What I can also confirm is that there have been deeper interventions in the engine control. Since the update, the electric motor actually hands over significantly smoother and without extreme power drop to the combustion engine. That's great, although it's quite a shame that it took so long.
As for the assistants, I cannot confirm that they are supposed to be less sensitive now. To me, they are just as picky and harsh as before.
Today, I first had the rear light defect error again. Let's see if it's the old (actually already fixed) error again or if there is actually a rear light that is defective.
 
The issue with the rear light seems to be that the start button is pressed while the light animation is still active (essentially pressing the button too quickly). A software update won't do much about that. When the animation is disabled, the rear light probably turns off faster, and the error may occur less frequently (but that's just hearsay). I can definitely confirm that the error always occurred when I was quite quick in starting (I still had the animation active).
 
If a manufacturer has already implemented such an animation, which is actually just unnecessary fluff, then it should also work in such a way that no errors are caused when you press the start button "too quickly." :D
 
How long does the animation take? Usually, I need a good 15-20 seconds from opening to pressing the button.
 
If a manufacturer has already implemented such an animation, which is essentially just unnecessary fluff, then it should work in such a way that no errors are caused when you press the start button "too quickly." :D
That's true, but it won't be fixed with a software update. Considering the willingness to address the issue of shock absorber knocking (which has existed since the pre-facelift), it's unlikely that they will focus on a comparatively less important topic that only arose with the facelift.
How long does the animation last? I usually need a good 15-20 seconds from opening to pressing the button.
No idea, but it could be around that time; just check how long it lights up after opening. I see the display at most 1-2 times a month, and since nothing beeps permanently, it doesn't bother me that much. It's just a notification, and it goes away with the next start.
 
I'm going to test that again later. Earlier, I waited extra long, and the error didn't occur. After the animation, the light stays on (it feels like) forever before it goes off. When I finish work, I'll hurry up and overwhelm the little VW :sneaky:😜
 
Then that's the coming/leaving home feature, where you can set the light duration in the settings to be shorter (e.g., 5 or 10 seconds).
 
So I have now tested it a few times deliberately. Especially quickly (3-4 seconds) after opening the vehicle, I pressed the start button. No error. Therefore, I would question an immediate causal relationship. Perhaps if you accidentally hit a specific point of the animation. But then it is even more likely a software error rather than the animation being causally responsible for it.
 
Okay, maybe you really have to catch a specific point in time. What I have passed on as a hint comes from several sources; I am not aware of any other reason. In any case, shortly after the purchase, I set the Coming-Home to 10 seconds, and since then, I have only encountered the error when I started (too) quickly, which is why it seemed plausible to me so far.
 
Small update on the rear light issue. I've been observing it a bit more closely for a while now and would completely rule out the light animation as the cause. It's set to 10 seconds for me (probably the default setting, I've never adjusted it). The rear light malfunction chime occurs most frequently for me after charging. Just due to the time it takes to unplug, etc., the 10 seconds are long gone by the time you turn on the ignition.

And before the update, I hadn't experienced the error for a long time (actually daily before that). So I assume that the error was fixed in the previous software and has now been reintroduced. Therefore, I also assume that the cause should actually be known (it was fixed once before). Unless it was pure coincidence and they accidentally patched it away. The more I think about it, the more likely that seems :ROFLMAO:
 
That's more due to the workshop.
In my case, the entire lighting was incorrectly adjusted; the corner light was aimed inward on both sides.

After the adjustment, the range of the low beam was okay again, the left strip is fine for the corner light, but the right strip is pointing outward to the right.
So it is somehow adjustable, but how, I have no idea. It took me about 20 minutes to sort it out. (And I had a service a few days earlier :mad:)

However, I haven't had it corrected again so far, as my time is too valuable for that. I have to wait until the next service or oil change, hoping that it will be correct then :rolleyes:
 
But watch out! VW hardly does anything on warranty or goodwill anymore. In the past, I always had everything done during the first inspection (except for very serious issues). It always worked without any problems. Nowadays, however, they say that anything not claimed and corrected within 6 months, you have to pay for yourself.

I've already experienced this several times myself :mad:
 
Outrage!!! It must also have something to do with the dealer. What my dealer has managed to get through with goodwill, even though my PHEV is now almost 6 years old and the previous owner had all the last inspections done at an independent workshop.
 
I have now also been invited to the software update PV4RC... It seems to be intended for all older Terras. I'll be surprised...
 
I have now also been invited to the software update PV4RC... It seems to be intended for all older Terras now. I'll be surprised...
Well then, good luck 🍀🍀🍀🙋🏻‍♂️
 
I have now also been invited to the software update PV4RC...
I have been driving around with the 2768 (from 2632) for a few days now, it took 3 days. Over the weekend, I experienced a phantom braking on the highway... The assistance systems have not failed yet, but it hasn't been cold enough either. The car is also sometimes open in the app. The only really positive thing so far is that I can now put the annoying attention warning into the quick menu to quickly deactivate it with the speed warning. It's great that one can also take joy in small things. :ROFLMAO:
 

* = Advertisement
Links marked with an asterisk (*) are affiliate links. If you click on one of these links and make a purchase, we receive a commission from the respective online shop or provider. This does not affect the price you pay.

Back
Top