Exhaust system Leon ST VZ

@ekm

Ich fand beim Leon war das Schubknallen der größte unterschied für mich zwischen Comfort und Individual "Pure".
 
Ja, das ist durch die geänderte Motorsteuerung, aber die (bereinigte) Lautstärke am Gas ist nicht so viel anders.
 
was das dröhnen bei bestimmten drehzahlen angeht, kann ich gut nachvollziehen. bei meinem aktuellen golf 8 gti cs fängt er im 7. gang bei 160-170kmh richtig an alarm zu machen. meine lösung ist schneller oder langsamer zu fahren, da es bei golf keine "pure" einstellung gibt. andererseits wäre eco oder komfortmodus die alternative, das ding abzustellen.
 
Weiß denn schon einer wo der blöde Stecker vom Soundmodul ist? Beim 5F war er quasi motorseitig auf der Unterseite der Wischerblätter montiert. Hier ebenfalls? Und spuckt er dann eine Fehlermeldung aus?
 
  • Like
Reactions: ekm
...

Beim Leon habe ich da nicht so ein Unterschied wahrgenommen (wenn man pure Sound engestellt hat). Ich glaube gelesen zu haben, dass man in den ST auch keine Klappenanlage einbauen (und zulassen) kann, da serienmäßig keine Klappe vorhanden ist.
Doch doch, Grail und Friedrich Motorsport haben da was im Angebot mit Klappe und Eintragungsfrei. :-) Die ist dann halt von 20-80 Kmh immer zu.
 
  • Like
Reactions: ekm
I can hardly imagine that a complete exhaust system is supposed to be registration-free. Exhaust tips, yes, but the exhaust system? Just for the reason that the exhaust system changes the emission values and noise levels, it is a reason for registration + approval at the TÜV. Could you send a screenshot of that?
 
Last edited by a moderator:
Complete systems can be exempt from registration as long as they have an ECE or TTG number. Previously, it was the ABE, but these have not been issued anew for several months. The values only change within the maximum permissible limits. There are plenty of complete exhaust systems that are exempt from registration, even with flap control. Only manually controllable flaps are not roadworthy and therefore illegal.

The manufacturer has the first exhaust system approved individually and applies for approval for series production. Then, as long as he does not make any technical changes to the approved prototype, he does not have to have a new individual approval done.
 
Well, I'm curious about that ^.^
 
The emissions values do NOT change with a system from the cat!

I still have a Ford Fiesta ST (2016), which originally has no flap; now it has one from Streetbeast (FMS) with ECE, no registration required. At the time of the system's approval, a closure was "only" required between 50-80 km/h. In this case, a small control unit comes along, which reads the RPM and speed and then closes or opens the flaps via vacuum.
 
It's just unfortunate when the flap or its mechanism rusts shut over time, and as a result, the open/close function no longer works. And then that's it with the MOT. Some stuff is so badly rusted that it can't be repaired anymore. I've experienced that several times myself.
 
But this should not be the case here as there simply isn’t enough time for it to rust away. Even if stainless steel sits unused for half a year, nothing rusts. Besides, the component is regularly moved.
 
It's just unfortunate when the flap or its mechanism rusts shut over time, causing the open/close function to fail. And then that's it for the MOT. Some parts are so badly rusted that they can't be repaired anymore. I've experienced that several times myself.
That's exactly why you're required to go for the MOT. As soon as certain defects develop over time, you are required to have them fixed. If you don't have a flap and then you get one, it's simply one more point that leads to wear.
 
@dtmdriver He is completely right – with my Ford Focus ST Estate, the emissions values after 100,000 km were still excellent and in the lower range (last MOT report), despite having a Milltek exhaust system installed (no registration required, as it has an ABE*).

As long as an exhaust system has an ABE*/ECE and complies with the stationary noise level including tolerance (see vehicle registration document), you don’t need to have it registered.
However, as soon as you start modifying the engine or the intake, the operating permit becomes void (ABE*/ECE becomes invalid) and you must have a combination approval carried out by the MOT.

This would also be the case, for example, with (non-OEM) wheels in combination with spacers. Because these two components affect each other.

Spacers and an exhaust system, however, would again be exempt from registration (if both have an ABE*/ECE).

*meaning an ABE without A01
 
That's right. (y)
 
It's just unfortunate when the flap or its mechanism rusts shut over time, causing the open/close function to fail. And then that's it for the MOT. Some parts get so badly rusted that they can't be repaired anymore. I've experienced that several times myself.
That has actually happened there (it wasn't moved for too long), but in that particular case it wouldn't have mattered anyway, since the system has two flaps and the one for quiet mode wasn't affected; it could be fixed with gentle force.
The MOT usually doesn't concern itself with the exhaust system's noise level for the certificate, as it's not safety-relevant. Of course, it can happen that with extremely loud systems, the tester might have some reservations.
 
Kurz weg von der Klappenanlage, ich habe es bei mir festgestellt und auch in einem YT Video, ist es sonst noch jemanden aufgefallen das beim Leon ST VZ die rechte Seite der AGA ein klein wenig nach unten „hängt“? Also sie nicht ganz in Waage mit der linken Seite ist? Z.B. wie im angehangen Bild. Man muss aber schon etwas genauer hinschauen.IMG_4540.png
 
Eine etwaig vorhandene Unsymmetrie stört mein Auge ebenfalls gewaltig, es ist auf Deinem Foto aber schwer zu erkennen, da das Bild sehr dunkel ist. Dafür sieht man deutlich, dass da jemand das ABT-Emblem völlig schepp auf die Heckklappe gepappt hat. Das Emblem geht von links unten nach rechts oben. Das würde mich immens stören.
 
Da die Abgasanlage ja links und rechts aufgehängt wird, kann das schon mal sein, dass sie "schief" hängt. Kann man aber in der Regel korrigieren.
Aber je nach Temperatur dehnt sie sich vielleicht auch mal leicht unterschiedlich aus
 

* = Advertisement
Links marked with an asterisk (*) are affiliate links. If you click on one of these links and make a purchase, we receive a commission from the respective online shop or provider. This does not affect the price you pay.

Back
Top