Help: Cable routing on tailgate damaged during dashcam installation

SirIsaac

War schon mal da
Hello everyone,

I've been driving my new Cupra Leon ST VZ for about a month now and I'm very satisfied. Even before I received the car from my dealer, it was clear to me that I wanted to install a dashcam with front and rear cameras to protect myself from potential "problems" on the road.

Since day one, I've been using the front camera, which I connected to the 12V socket in the centre console. That has worked well so far, and I want to stick with it for now, even though I also bought a hardwire kit.

Today, I wanted to install the rear camera, which is not entirely straightforward due to the cable routing. I did some research beforehand and watched a few videos to avoid mistakes. It was particularly important to me to route the cable invisibly within the vehicle.

Everything actually went well, but when I wanted to reassemble everything, I noticed a mishap: I damaged the attachment of the cable channel on the tailgate. Although I thought I was being careful enough, the little nub that presses the channel watertight against the body partially broke off

Ideally, I would like to replace the entire part, but that's problematic as I could lose the warranty (work on the vehicle's electronics). Alternatively, I thought about gluing the channel to the body, but I'm unsure about that. I hope someone here in the Forum can give me a Tipp on how to repair the damage and restore the watertightness. I'm afraid that the electronics in the rear or the headliner will be damaged by incoming water.

Thank you in advance for your help!
 

Attachments

  • IMG_8854.jpeg
    IMG_8854.jpeg
    2 MB · Views: 64
  • IMG_8856.jpeg
    IMG_8856.jpeg
    1.6 MB · Views: 64
Ich würds auf jeden Fall tauschen und mir weniger Sorgen um die Garantie, als um eindringendes Wasser machen.
Es gab im Skoda Karoq Forum jemand, bei dem genau durch das Teil über Monate unentdeckt Wasser ins Auto lief. Bis er es gemerkt hat, war hinten schon alles nass und verschimmelt.
Also nochmal ran, solange das Wetter gut ist.

Blöd ist nur, dass du alle Kabel trennen musst, die durch die Tülle führen und evtl. auch Steckverbinder zerlegen, die nicht durchpassen, Verkleidungen abbauen,...

Vielleicht auch vorher die Batterie abklemmen.


Das hier (nr. 2) sollte das passende Teil sein. 9,24 lt. Katalog.
Screenshot_20250810-082515~2.jpg
 
Danke für eure Antworten!

über Monate unentdeckt Wasser ins Auto lief
Genau das will ich vermeiden und bin auch froh, dass es mir aufgefallen ist.

Ich werde es lieber von einer Werkstatt machen lassen und morgen mal in ein paar anrufen. Wie du sagst, müssen hier ja die Kabel alle wieder durch die neue Tülle durch und das lasse ich dann lieber fom Profi machen, als noch mehr zu beschädigen.
 
Ich glaube das Teil zu besorgen wird das geringste Problem. Das Alte kann man ja zerschneiden, aber durch das neue Teil müssen alle Kabel gezogen werden, das dürfte nicht einfach werden..
 
Ich habe damals auch versucht das Kabel für die Dashcam dadurch zubekommen. Mir ist die gleiche Nase ebenfalls abgebrochen und ich habe das Kabel auch nicht durch diese Gummitülle bekommen...

Das austauschen ist dann wie schon gesagt natürlich ein Krampf..alle Kabel abziehen und dann dadurch..
 
Ich hatte es zweimal ab und das Kabel durchgezogen und wieder raus. Ist eigentlich nicht so schwer. Man muss die (angebrochene) Nase mit einem flachen Schraubendreher etwas rein drücken (mit Gefühl) und dann geht das auch problemlos ab.
 
Kenne das noch von einem anderen Auto, beim verbauen der neuen Heckleuchten gab es ein ähnliches Gebastel.
Für die Gummitülle hilft Silikonöl, damit flutscht es ganz gut. Vorher natürlich eventuelle Stecker abkleben.
 
Ich habe gerade nochmal geschaut die 5G69771829B ist die richtige Teilenummer. Kostet 10,94€ Netto.
Das Teil zu erneuern und entsprechend die Kabel zu ziehen hat 309€ Netto gekostet. Das ganze lief bei mir jedoch eh noch unter Garantie weil was anderes an der Heckklappe/am Auto gemacht werden musste.
 
Kleines Update: Hab's jetzt vom :) reparieren lassen, der mich gestern zum Glück noch zwischenschieben konnte. Kostenpunkt ca. 160 €, aber ich kann in ruhe schlafen, wenn es regnet.

Sowas dummes... das wird mir (hoffentlich) nicht nochmal passieren...

5G69771829B ist die richtige Teilenummer. Kostet 10,94€ Netto.
Das Teil müsste es auch genau gewesen sein, weil die Kosten auch so auf der Rechnung aufgelistet sind :D
 

* = Advertisement
Links marked with an asterisk (*) are affiliate links. If you click on one of these links and make a purchase, we receive a commission from the respective online shop or provider. This does not affect the price you pay.

cupra.forum · Alle Rechte vorbehalten · Dies ist kein Forum der Seat Cupra S.A.U.
Back
Top