Imprints on the roof rails from Thule roof racks

Welcome! You have been invited by Gand-Alf to join our community. Please click here to register.

Pavel

Kennt sich aus ★
Hello everyone,

After fitting a Thule roof rack to my Cupra Leon ST, I unfortunately noticed marks on the roof rails. There are now elongated marks visible at all four contact points (see picture). Polishing has so far hardly helped.

For your information: I tightened the racks with a torque wrench, so I can basically rule out overtightening.

Has anyone experienced something like this before? Is it possible to remove the marks again, or does anyone know what causes them or how best to deal with them?

Thanks in advance!
 

Attachments

  • IMG_5376.png
    IMG_5376.png
    4.8 MB · Views: 74
Ich kanns dir nur sagen wie umgehen: Transparente Steinschlagschutzfolie drauf.

Spürst die die Stelle mit dem Fingernagel? Wenn nicht, sollte Politur klappen.
 
after the installation of a Thule roof rack

so, I only know that THULE is extremely accommodating (in two cases, a defective part was replaced free of charge without discussion) and has a "Produktfinderon the HP has.

In this respect, I would -without doubting it- first ask if you have the appropriate carrier system for your Leon.

Secondly: the rail on our 1.5 TSI stands significantly higher above the roof than in your photos, and the "EVO Raised Rail Foot Set" is from 2019. However: it has not left any permanent marks so far. A torque wrench is all well and good. The assembly instructions from 2019 state a tightening torque of 4 Nm. Here too, I assume that you have taken that into account. I always tighten the feet manually, with the motto: "after tight comes off. And after off comes a reprimand.

4 Nm - Kopie.jpg

Also, the question arises whether the roof rail can "withstand" the torque 🤷‍♂️
 
Last edited:
Also, die Dachträger sind auf jeden Fall passend für den Leon und auch die 4 Nm habe ich beachtet. Durch den mitgelieferten Drehmomentschlüssel geht das ganz gut.

Für mich stellt sich die Frage ob sich die Abdrücke wieder entfernen lassen?
 
@Pavel dafür wäre es wichtig die Art der Beschädigung genau zu kennen...

Für mich sieht es so aus, als wäre der Klarlack gedrückt worden, dann wird polieren etc nichts bringen. Es müsste viel mehr einmal neu lackiert werden (mit Klarlack).
 
Hey,
ich habe genau dieselbe Problematik.
Ich habe die Thule Wingbar Edge, die ich vorher mehrere Jahre ohne Probleme auf dem Ford Focus genutzt habe, auf dem Cupra im Einsatz. Ich habe, so wie Thule es fordert, den Fußsatz getauscht und nutze natürlich auch nur den mitgelieferten Thule Drehmomentschlüssel. Auch reinige ich die Stellen der Montage vorher auch gründlich, kann also auch Abschürfungen durch dazwischenliegenden Dreck/Sand ausschließen.
Diese "Stigmata" habe ich leider trotzdem seit der ersten Montage auf der Reling - da ist definitiv die Lackierung beschädigt.
Unternommen zwecks Gewährleistung habe ich noch nichts.
 
Ich hatte bei meinem ST zwar nichts an der Reling befestigt mir ist aber beim putzen damals schon aufgefallen, dass der Lack unglaublich weich zu sein scheint. Ich hatte Vogelkot entfernt und nach dem finalen trockenwischen (mit einem dafür vorgesehenen weichen Tuch) direkt Riefen drin.
 
Hello dear Cupra friends, I am new here. I just got my Leon ST VZ Black Edition and mounted the roof rack from OWEN for the vacation. I am a bit surprised that no torque is specified and no torque wrench was included. I tightened it by hand to avoid damaging the paint. The inside is lined with rubber plastic, but the outside is not, so the metal rack directly contacts the paint. Does anyone have experience with this and can tell me if I need to pay attention to anything else besides the paint protection film? Next week the car will get a ceramic coating. Should that area be free? What torque should I use to tighten it? I ordered a torque wrench and would correct it afterwards, but 4Nm seems a bit low for this system. Thanks in advance for the answers. Best regardsIMG_5839.jpeg
 
I had the same problem with the Thule mounting system on my Seat Leon Cupra ST (5F).

The roof rails were painted in a matte black finish. After the required installation, I also had scratches that wouldn't come out.

That's why I haven't ordered new mounts for my new Cupra Leon VZ yet, as it really annoys me... Good to read here that it seems to still be the case with the new mounts. Then I won't be putting any roof rack on it anymore. Except maybe with a protective film.

Very frustrating, I think...
 
Hello dear Cupra friends, I am new here. I just got my Leon ST VZ Black Edition and mounted the roof rack from OWEN for the vacation. I am a bit surprised that no torque is specified and no torque wrench was included. I tightened it by hand to avoid damaging the paint. The inside is lined with rubber plastic, but the outside is not, so the metal rack directly contacts the paint. Does anyone have experience with this and can tell me if I need to pay attention to anything else besides the paint protection film? Next week the car will get a ceramic coating. Should that area be free? What torque should I use to tighten it? I ordered a torque wrench and would correct it afterwards, but 4Nm seems a bit low for this system. Thanks in advance for the answers. Best regardsView attachment 4184
Hi, you should definitely follow up on that. Owen specifies about 9Nm.
 

* = Advertisement
Links marked with an asterisk (*) are affiliate links. If you click on one of these links and make a purchase, we receive a commission from the respective online shop or provider. This does not affect the price you pay.

Back
Top