Self-built accessories

@Milan
Or you can design it as a kind of "clip" for 3-5 coins that you clamp into the recess, it should possibly also work without glue.

Edit: Short sketch attached
 

Attachments

  • IMG_7207.jpeg
    IMG_7207.jpeg
    1.7 MB · Views: 34
Last edited:
I can't make much use of the key compartment. I found it better in the pre-facelift version, as the 2 compartments were longer and deeper. Therefore, I would prefer a storage area that fills the shape of the key compartment at the bottom and perhaps also supports itself in the gap to the upholstered side panel of the center console (with an additional brace). The storage area could then be roughly the size that it ends in length at the top like the key compartment and at the bottom at the auto hold switch, with the width extending to the right up to the copper frame and to the left up to the seam of the side panel. In a tub shape, about 2 cm deep. I hope my thoughts can be understood. :unsure:😁

There, for example, one could securely store a larger remote control for garage doors, a keychain, or other larger items. If there were your custom opener for all systems, that would of course be 1000% nicer and more practical, but that is just a one-off.

Edit: I tried to sketch this out. In red, roughly the area, and in blue, the support walls at the bottom.

20250131_134319.jpg
 
Last edited:
Also mein Garagentoröffner funktioniert prinzipiell für viele Systeme, das ist eine anlernbare Universalfernbedienung von ebay. Hat so natürlich nur Platz für einen Knopf

Servus @Milan,
Wie wäre es mit einer Art Kartenhalter für mehrere (3-4) Tank- / oder z.B. Zeiterfassungskarten?
Prototyp ist im Druck :)

@Milan
Oder man gestaltet ihn als eine Art "Spange" für 3-5 Münzen den man in die Mulde klemmt, sollte evtl. auch ohne kleben funktionieren.
Ich hab's mal frei Interpretiert:

1749751961336.png
 
@ST4N
So sieht's momentan aus, Cupra hat an der Unterseite praktischerweise einen Spalt gelassen, so dass die Halterung einfach von unten eingeschoben werden kann. und baut auf der Unterseite der Armablage etwa 12mm auf... was meinst Du zur Position, wäre das praktikabel?

PXL_20250613_075704744.jpg

Leider lässt sich das Fach so nicht ganz schließen.. dafür müsste alles noch 1-2cm nach oben rutschen (liegt sonst auf dem schmaleren Münzfach auf)

...wie ergonmoisch das zu bedienen ist hängt wahrscheinlich auch mit der SItzeinstellung zusammen.. muss ich nachher mal testen :D
 
Ich glaube es wäre praktischer, wenn es in der Position bliebe und nicht auffächern würde, sonst würde es auch in höherer Position zu Problemen kommen, wenn das Fach voll ist.
Könnte aber zu ausgerenkten Schultergelenken führen, generell an die Stelle zu kommen, je nachdem wie beweglich man ist bzw. an welcher Position der Sitz ist. 😁
 
@Milan Richtig gut umgesetzt! Ich persönlich schließe das Fach eh nie komplett, da ich die Armablage etwas angewinkelt nutze.
Bzgl. der Praktikabilität (wie von dir schon angeführt) würde eine Verlängerung im unteren Bereich um 1-2cm nicht nur das schließen sondern auch eine mittigere Positionierung und ggf. komfortablere Entnahme ermöglichen. 😊

PS: Wie sieht denn aktuell die Rückansicht der Konstruktion aus?
 
Sehr schön!
Heißt du bräuchtest bei einer Verlängerung um 1-2cm noch eine Art Anschlag für die untere Karte, damit diese kein Spiel hat, korrekt?
Könnte man ggf. durch einen Steg oder Verstrebung realisieren. Bringt evtl. auch nochmal bisschen Stabilität in sich. Wobei die schon ganz gut sein dürfte.
 
Mega cool!! :D
Ergonomie: ich hätte die Öffnungen vielleicht eher zum Beifahrer hin gemacht - dann muss man die Karten nicht "gegen sich" ziehen, sondern von einem weg - entweder da ist "frei" (leichter für einen selbst) oder der Beifahrer könnte auch behilflich sein ;)
 
Eigentlich muss ich nur die "Lasche" unten etwas rausziehen, das ist kein Thema. Mehr Kopfzerbrechen bereitet mir da eher die Druckerei an sich, die Konstruktion ist nicht gut optimierbar für einen sauberen Druck :unsure:
 
What comes to my mind and might be quite interesting for electric/hybrid drivers:
Similar to your umbrella holder, one could design a larger version for hanging the charging cable.

The image is just an example and would need to be equipped with a clamp on the back.
I could also gladly provide measurements regarding the contact surface for the cable bundle.
 

Attachments

  • Halterung Kabel.PNG
    Halterung Kabel.PNG
    500.5 KB · Views: 8
Last edited:
@ST4N
Der Münzen-Entklapperer wäre soweit fertig. Wenn Du oder jemand anders das Teil haben möchtest -> wie immer PM an mich.

1749913611764.png
(Denkt euch das Flauschband weg, der Halter passt ohne)

Der Karten-Halter wird tatsächlich eine Herausforderung, ich habe heute 2-3 Designs durchprobiert aber so wirklich zufrieden bin ich damit nicht 😁
 
Wer um 24 Uhr Kaffee trinkt, hat wirklich Langeweile 😁😉
 
Live Daten in der Signatur? interessantes Feature 😉
 
Back to topic 😋

Nach 8 Stunden in der Werkstatt, ordentlich verheiztem Material und Werkzeug.. dafür mit viel Neuer Erfahrung habe ich zumindest ein Exemplar zustande gebracht :cool:
View attachment 1362

@Melfinos Da Du die Idee eingebracht hast: Falls Du den "Einkaufswagenlöser" haben möchtest (und Dir farblich passt 😋), schick mir bitte eine PM. Ansonsten gibt's wieder eine Verlosung :)

Der Aufwand (und auch die Materialkosten) dafür war leider höher wie gedacht, daher habe ich keine weiteren Exemplare, ist also tatsächlich ein Einzelstück. Ich bin schon dabei die Herstellung zu vereinfachen - sollte dabei was brauchbares rumkommen, gibt's im Marktplatz einen entsprechenden Thread dazu (Außer jemand will das Teststück aus der "Massenfertigung" haben, das hängt grade zum trocknen... auch hier PM an mich).

@Milan
Das Unikat ist bei mir sehr gut verpackt angekommen. Auch die nette persönliche Beilage fand ich super. (y) :love:🍻

Vielen Dank

1000022358.jpg
 
Den runden Teil mit dem Logo und dann mit der gleichen Breite fortsetzen + Schriftzug, Hinterende nochmal abrunden, Loch rein.... dann ist es ein richtig geiler Schlüsselanhänger!
 
Update on the card holder:

R62_7267-Verbessert-RR.jpg1750002356421.png

It is now a two-part construction that can be clamped securely and stabilized against wobbling with a piece of double-sided tape.

Printing time is about 7 hours + 20 minutes of post-processing. The test piece is currently on its way to the testing center; let's see if it goes into production :ROFLMAO:



@Schmitzibu You mean like this?
b5f087c8-805b-4685-9e57-3eedafe9156a.PNG
 
Last edited:
Den runden Teil mit dem Logo und dann mit der gleichen Breite fortsetzen + Schriftzug, Hinterende nochmal abrunden, Loch rein.... dann ist es ein richtig geiler Schlüsselanhänger!
Ich habe zwei "Einkaufswagenlöser" am Schlüsselbund - Edelstahl und ohne Cupra Schriftzug: die Rundung bzw Kante kann schon sehr wichtig sein, manche Wagen lösen sich erst mit etwas mehr Druck nach rechts ist links.. ohne die Kerbe kann man nicht nochmal nachjustieren, so meine Erfahrung aus der Praxis.
 
@Milan Yes! Exactly like that! How big is it? Will the logo be on both sides? Could we write Terramar on the back instead of Cupra?

@coopra I meant as a trailer and not as a solver..
 
Last edited:
@Milan Yes! Exactly like that! How big is it? Will the logo be on both sides? Could we write Terramar on the back instead of Cupra?

Will this be an order? 😁

Since I have to cut the part out of a large sheet anyway, it can be as big as you want. In the picture, it would be exactly 23x65mm.

Since etching is really tedious and the effort is not insignificant, I would solve the Cupra logo and the lettering with a corresponding plotted foil, so it can say whatever you want. I would sink the Cupra logo slightly into the material, but only on one side.

If there are more interested parties for such a pendant, I can gladly make a handful: with a one-sided CUPRA logo and "CUPRA" lettering, on the other side model name or desired text.

cbbb2e6d-981f-4ccf-b894-0b92b83daf73.PNG

Feel free to create a poll (y)
 
Last edited:

* = Advertisement
Links marked with an asterisk (*) are affiliate links. If you click on one of these links and make a purchase, we receive a commission from the respective online shop or provider. This does not affect the price you pay.

cupra.forum · Alle Rechte vorbehalten · Dies ist kein Forum der Seat Cupra S.A.U.
Back
Top