The window lifter/window switch is not working properly.

Angela

War schon mal da
Hello everyone,
I drive a Cupra Formentor E-HYBRID and I've noticed that the driver window switches are not functioning properly.
When I push the lever down, the window goes down a bit. When I want to raise it again, I press the switch to close... But the window still goes all the way down first.

The other windows work perfectly.
What could be the reason for this?

Thank you for your help.

Best regards
 
Good morning, try pressing the open button on your key until all the windows open, and then press the close button until all the windows close. Maybe the system needs to be taught, or you can use the emergency key to unlock and hold it until all the windows go down, and vice versa with closing. Good luck!
 
After a relearning, everything should work as it is supposed to.
 
When I push the lever down, the window goes down a bit. When I want to raise it again, I press the switch to close it... But the window still goes all the way down first.

That initially reads as if the window regulators need to be re-learned hierThe window lifters are pre-programmed to two stop points ("learned") to ensure the functions "Comfort Opening" and "After-Run." Upper stop point = window fully closed, lower stop point = window fully open. It can happen that the window lifters forget what they once learned. However, this is no reason to worry; just re-"learn" them, see link.

Another question: does the central locking still work? If not, the door control unit could be defective.

But first, try re-learning the window lifters.
 
Hello, thank you very much for the Tipp. I tried it, but it still doesn't work.

Best regards,
Angela
 
still doesn't work

so, it's only about the window regulator on the driver's door, the others are fine and the central locking works too.

Generally speaking: the Cupra probably has the same tilt/pull switches (four) in the driver's door. If you press a switch briefly, the corresponding window goes down a bit, just as you describe. If you press the button a little longer (the window is not all the way down yet), the "after-run" kicks in

This would mean you haven't activated the "after-run." Maybe just a "mü" not right now. Perhaps the window regulator will catch up on the "after-run" the next time you press the button. 🤷‍♂️

Specifically: you write "When I want to raise it again, I press the switch to close." With the ROC, you have to pull the switch up to close the window, not press it.

Assumption/thought: if you press the switch again, the window logically goes down. But you want to close it and might therefore be holding the button down. Could it be that the window regulator consequently skips the lower stop point and goes back up? That shouldn't be possible, as that would be the "learning." 😒

Or does the Cupra have different buttons? Then I'm unfortunately at a loss.

How does the window regulator behave during "comfort opening/closing" (with the key)? Does that work flawlessly? Then, in my opinion, at least the door control unit should be fine, so that "learning" the key and the central locking is unnecessary. Maybe only the switch is defective.

One more thought: does the Cupra possibly have a resistance detection when closing the windows? Could it be that at some point a resistance was detected and therefore the closing was interrupted? I could imagine something like that especially with the heavier acoustic glazing (the motor has to work harder).
 
Hello Angela,
I had a Leon where the window regulators had to be replaced.
The problem was: I opened the window a little and wanted to close it again after a few minutes.
However, the window kept going all the way down because the pinch protection was reacting.
Cupra is aware of this problem. It affects some people, including vehicles from the VAG group (Skoda and VW).
Relearning and resetting did not help.
Only a replacement of the window regulator worked.
I had 3 windows affected.
There is a thread about it in the Leon Forum.
 
I'm experiencing the same problem now. First on the front passenger side, and for the last three days also on the driver's side (even worse). It always goes all the way down before I can raise it, and most of the time I also have to hold the switch until it is up. Today it was even worse; I closed the driver's side and then it opened a crack by itself immediately, twice in a row.

I already have a workshop appointment on Monday. Let's see what they say and do.
 
Unfortunately, it was a long journey for me. I believe I was there a total of 6 times. First, the window regulators were replaced, and then the motors. I hope it goes faster for you :-)
 
Hello, has it happened before that you pressed and held the button on your key while opening until all the windows go down for about 5 seconds, and then you close it and hold for another 5 seconds?
 
With the remote control, both opening and closing works for all four windows, but the problem persists otherwise. It goes down instead of up, goes up and immediately opens again (and this happens multiple times in a row), the lift automatic doesn't work... I was able to demonstrate it to the workshop employee immediately; it just keeps happening. He mentioned that they recently had a Cupra with similar problems and all the window regulators were replaced.

I thought it could be resolved through reprogramming or software, but apparently not. If the window regulators need to be replaced, there will be a follow-up appointment, and unfortunately, I will have to drive around with the problem for 3000 km on vacation. Well, it could be worse; the car drives normally.

Let's wait and see; I dropped off the car this morning, and no one has contacted me yet.

Oh, and video evidence was once again a must because, well, it's a Cupra...

For me, it was unfortunately a long journey. I think I was there a total of 6 times. First, the window regulators were replaced, and then the motors. I hope it goes faster for you :-)
My condolences. Before it comes to that, I’d rather learn to live with it.
 
With the remote control, both opening and closing works for all four windows, but the problem persists otherwise. It goes down instead of up, it goes up and then immediately opens again (and this happens multiple times in a row), the lift automatic doesn't work... I was able to demonstrate it to the workshop employee immediately; it just happens all the time. He mentioned that they recently had a Cupra with similar problems and all the window regulators were replaced.

I thought it could be resolved through reprogramming or software, but apparently not. If the window regulators are replaced, there will be a follow-up appointment, and unfortunately, I will have to drive around with the problem for 3000 km during my vacation. Well, it could be worse; the car drives normally.

Let's wait and see; I dropped off the car this morning, and no one has contacted me yet.

Oh, and video evidence was once again a must because, well, it's a Cupra...

My condolences. Before it comes to that, I'd rather learn to live with it.
I thought the same. But with a purchase price of € 40,000, I do want those things to work. People fly to the moon, but functioning Cupra window regulators might still be a challenge :) :)
 
So I picked up the car again today. Only the window regulator on the front passenger side was replaced because the one for the driver’s side is not available directly. So, another appointment is needed.

The service employee mentioned that he will try to get Cupra to approve the replacement for all four window regulators because the one on the rear passenger side is also acting up. There is already a TPI for the front, the problem is known, but not yet for the rear. He also said that thanks to my video, Cupra can see that the problems can also occur at the back. However, I think it will take more than just my video for a TPI for the rear, so send yours out too. The more Cupra receives, the better for all drivers. In any case, I am hoping for a case-by-case decision regarding the replacement at the back.
 
Yesterday we picked up our Leon again. Here, only the passenger side was replaced. The driver's side is delayed,
 
I picked up the car again today. Only the front passenger window regulator was replaced because the one for the driver's side is not available directly. So, another appointment is necessary.

The service employee mentioned that he will try to get Cupra to approve the replacement for all four window regulators since the one on the rear passenger side is also acting up. There is already a TPI for the front, the problem is known, but not yet for the rear. He also said that thanks to my video, Cupra can see that the problems can also occur at the back. However, I think it will take more than just my video for a TPI for the rear, so please send yours out as well. The more Cupra receives, the better it is for all drivers. In any case, I am hoping for a case-by-case decision regarding the replacement at the back.
I sent you at least 2 videos for all 3 defective window regulators. After the first replacement of the 3 window regulators, 2 were defective again. Then apparently the motor itself was replaced after only the window regulators were changed before. At the moment, it is working.
 
Aja, they are just trying to get away with it as cheaply as possible. It's annoying for us if we only get one thing replaced but the other still has problems. Follow-up appointments are so much fun!
 

* = Advertisement
Links marked with an asterisk (*) are affiliate links. If you click on one of these links and make a purchase, we receive a commission from the respective online shop or provider. This does not affect the price you pay.

Back
Top