Notrad at the Cupra Leon ST VZ (333PS)

Welcome! You have been invited by Gand-Alf to join our community. Please click here to register.

kuchen25

Kennt sich aus ★
Germany
Hello everyone,

you can't order a spare wheel from the factory for the Cupra Leon ST VZ (333PS).
  • Do you actually always get a tyre repair kit instead?
  • Is it possible to retrofit a 19" spare wheel ("insert") afterwards? Or is that simply not possible with the VZ (perhaps because of the 19")?
Unfortunately, I also can't really find pictures of the non-VZ with a spare wheel.

In my imagination: You disconnect the subwoofer, lift it out, place the spare wheel in the recess, put the subwoofer inside the spare wheel, and reconnect the subwoofer.

I found a spare wheel here: https://www.autonotrad.at/p/set-not...luessel-wagenheber-huelle-fuer-den-wagenheber
 
Bei cupra ist es üblich dass du entweder/oder hast. Ich hab gesehen ich habe auch kein notrad, aber in der Tasche mit dem Bordwerkzeug ist ein Reifenkit.


Gesetzlich vorgeschriebenen ist in Deutschland weder das eine noch das andere. In Italien hingegen schon.
 
Does anyone here perhaps have the spare wheel configured in their Cupra Leon ST? If so, where is the tool (jack, etc.) stored? Is there even a foam insert in the trunk floor?
 
Yes, under the spare wheel is a small Styrofoam insert with the jack and so on.
 
Bei mir sieht es unter dem Kofferraumboden (und unter dem Sennheiser Subwoofer) so aus:

cupra_notrad_01.jpgcupra_notrad_02.jpg

Sieht das bei dir (Nicht-VZ) ähnlich aus? Wo würde da noch eine Styroporeinlage für Wagenheber etc. reinpassen?
 
Hab mir heute mal kurz die Mühe gemacht und alles frei gelegt, so sieht es bei mir aus;

Notrad mit Subwoofer
20251230_154726.jpg
Darunter dann die Styroporeinlage mit dem Equipment
20251230_154504.jpg
 
Mega, danke dir!

Der doppelte Ladeboden geht immer noch, oder ist dann das Rad zu weit oben?

Die Styroporeinlage dürfte dann die Teilenummer 5F9012109B haben. Vielleicht muss man die zentrale Schraube austauschen wegen der Länge, da gibt es die Teilenummern 5Q0803899 (Cupra, 127mm) und 1K0803899D (VW, 109mm). Laut ETKA braucht es bei der Styroporeinlage die 5Q0803899 (Cupra, 127mm). Da muss ich noch mal schauen, welche ich hab.
 
Doppelter Ladeboden geht. Ich habe mir extra noch ein zweiten Boden für untendrunter gebastelt (gibt's hier auch ein Thema dazu).
Ja, ich denke da wird die längere Schraube notwendig sein.
 
The polystyrene insert (5F9 012 109 B) has arrived today and, as far as I can tell, it fits.

However, it cannot be screwed down, as the screw (5Q0 803 899 from factory in my case) is too short (12.7 cm) and the "plastic nut" doesn't even reach the screw thread.

@ekm What part number do you have there? It should be written centrally on top, even in the installed state. It would be great if you could check that again 😁 The subwoofer is otherwise identical (6C0 035 621 A). Or am I missing something completely trivial?

Don't be surprised that the spare tyre is still missing—I wanted to order it only after sorting out the tool kit. I assume the spare tyre will be placed on the Styrofoam tool kit with the "rim-outside/view/road side" facing down, then the subwoofer goes in, while the plastic screw through the centre keeps everything centred.

cupra_notrad_schraube_zu_kurz.jpg
 
Last edited:
I'll check this afternoon; if I forget, send me a PM tomorrow. ;)
 
Etwas verspätet aber zu Mittagspause viel es mir wieder ein..
20260109_114642.jpg
 
Ah, super, danke dir!

Deine Schraube (5F0 803 899) ist tatsächlich nochmal länger als die bei mir ab Werk verbaute (5Q0 803 899). Die ist nun auch nachbestellt. Interessant ist, dass die mir im ETKA gar nicht aufgelistet ist und bei den Händlern auch nur als kompatibel mit dem Seat Leon III (5F) angezeigt wird. Naja, was solls :D
 
  • Like
Reactions: ekm
So, it's done.

I didn't install the standard 125/70 R18 spare tyre (which is normally supplied with the Cupra Leon), but instead fitted a 125/70 R19 spare tyre (from the Cupra Formentor). The diameter (and thus rolling circumference) of the spare tyre is closer to that of the standard production tyres:
  • Standard tyres 235/35 R19: 647.1mm
  • 18" spare tyre 125/70 R18 (standard): 632.2mm (-2.3%)
  • 19" spare tyre 125/70 R19: 657.6mm (+1.6%)
This should be gentler on the front axle differential and especially on the rear axle torque splitter. I believe the torque splitter is also the reason why a spare tyre isn't available as an option from the factory, as they're likewise not available for the Golf 8 R or the Audi S3/RS3.

The spare tyre also fits on the front axle with the Cupra-VZ brake system (I think it's a branded Brembo with the facelift?).

If anyone still wants to retrofit it, here's what I needed based on the Cupra Leon ST VZ 333PS MJ26:
  • Tool kit made of styrofoam (5F9 012 109 B)
  • Screw including plastic nut (5F0 803 899) – replaces the factory-installed one (can be removed by pressing down and rotating 90°)
  • Spare tyre (the 125/70 R19 also fits very well in the well)
The load floor can also be adjusted further down to the lower level, but then it lies flat on the spare tyre.

notrad_final1.jpg

Danke @ekm for the many searching :)
 
Last edited:
Was du bei deiner Betrachtung aber vernachlässigt hast, ist dass der tatsächliche Abrollradius vom Serienrad geringer ist. Der Reifen gibt ja auf Grund des größeren Volumens und des geringeren Druckes mehr nach, als der vom Notrad. Der tatsächliche Abrollumfumfang (ausgehend von tatsächlichen Radius) verhält sich somit anders. Deshalb schätze ich, dass mit dem größeren Notrad die Abweichung dann tatsächlich größer sein könnte. Kann mich aber auch täuschen, dass müsste man messen (also den Radius (Boden zur Nabenmitte) aller drei Varianten im montierten Zustand (nach "3m" rollen) vergleichen.
 
I can measure that soon.

When I mounted it yesterday to check the clearance of the brake, I noticed that it is really damn similar in size to the stock wheel.

Maybe it's also generally exaggerated because you only drive a few kilometers at 50-80 km/h, so the differential or the torque splitter probably doesn't get too hot yet. You can also normally drive longer curves.

Maybe the car also disables the all-wheel drive or the entire rear axle by opening the clutches when it detects that the rolling circumferences are permanently different.
 

* = Advertisement
Links marked with an asterisk (*) are affiliate links. If you click on one of these links and make a purchase, we receive a commission from the respective online shop or provider. This does not affect the price you pay.

cupra.forum · Alle Rechte vorbehalten · Dies ist kein Forum der Seat Cupra S.A.U.
Back
Top