Self-built accessories

Zu dem Becher... Coole Idee und Interesse melde auch ich schonmal an, sofern für den TM passend (wie kann ich beim Ausmessen behilfluch sein?).
Auf den Bildern die ich gefunden habe, scheint sich die Form zumindest grundsätzlich zu ähneln. ich schick Dir die Tage mal ein paar Schablonen zum ausdrucken mit Anweisungen zu. Im Leon hat der Cupholder z.B. einen Absatz auf etwa 30mm Höhe, die gibt es im Terramar nicht.

Wenn du also in deinem Becher innen einen Ring am Oberrand einplanen könntest, dann könnte man diesen Becher auch als Mülleimer verwenden.
Danke für den Vorschlag, ich spiele damit mal etwas rum. Die Schwierigkeit wird, das so zu designen, dass es einerseits ausreichend fest klemmt, andererseits aber komfortabel zu entfernen ist. Aufgrund des Druckverfahrens in Schichten ist das nicht ganz so einfach, weil ich gewisse Toleranzen nicht unterschreiten kann, die aber für sowas tlw. nötig sind (alles unter 0,1mm ist quasi Glück)

1752358344843.png
Hier mit mehr Dreeicken :) So in die Richtung? Mir gefällt es nicht so, im Innenraum arbeitet Cupra ja tatsächlich eher mit geschwungenen Linien.

@Milan
ich könnte mir für das vordere Fach eine art teiler vorstellen, wäre das mit deinem drucker machbar.
Machbar schon, im Moment ist mir da das messen aber zuviel Aufwand. Die USB-Ports müssen ja gut erreichbar bleiben usw... Aber danke für die Idee!
 
@Milan danke, wenn du mal zeit und lust hast, wäre ich ein abnehmer für den Teiler.

Im den USB Anschlüssen hätte ich ein verlängerungskabel und bräuchte da nur eine Aussparung, dass das kabel nicht gequetscht wird.

und da das teil herausnehmbar wäre, käme man sicher auch bei bedarf an die Anschlüsse.

ich kann ja mal versuchen zu messen und eine skizze machen. eigentlich müsste es für meine zwecke nur eine art brücke sein, die einfach das fach in gewisser höhe teilt.
 
Der Deckel gefällt mir gut. Erinnert ein bissle an den Airbag im Lenkrad!
Beim TM ist die Bechereinheit weiter vorne. Dort wäre ein Deckel, der zur Beifahrerseite aufklappt besser. Also in "Türsprache" Din-rechts angeschlagen.
 
@Schmitzibu

If you like, please:
  1. Print templates 1:1 on A4
  2. Place the "Bottom" centred in the rear cupholder and take a photo from above (ideally it fits with 2-3mm clearance)
  3. Hold the "Top" centred in the cupholder so that it is flush with the upper edge and then estimate the size of the gap between the template and the edge (ideally here too about 3-4mm clearance)
  4. Measure the height of the cupholder (i.e. the distance between the two templates)
 

Attachments

Three posts in a row, I’m sorry 😭

I also brought the version with the triangles into real life again. To get the surfaces reasonably smooth and avoid ugly stair-stepping, I printed the part “upright”. If this becomes the design you prefer, the resolution will be a bit finer (layer height here: 0.25mm, in the final product then 0.1mm).

What do you think?
R62_8830.jpg
 
@Milan

First of all, huge respect again for the work and the brainpower you put into this for all of us.

Regarding the design, I think both are good and, if in doubt, I might even "offer" both.
That way, everyone can choose whichever they personally prefer.
At the moment, I would also go for the second design, as I somehow find it more fitting for Cupra.

Best regards and thanks again to you at this point!
 
I have to say I really like both designs!
Decision: difficult! :D

To ask differently: What is the time required for each variant? (pure printing time + possibly post-processing)
 
We need to give the variants names, otherwise I keep getting confused...

Print time always includes cup + lid
Post-processing is the removal of support material, deburring, and "fitting".

So:
Variant 1 "Curved Lines": 3h45 print + 15 minutes post-processing
Variant 2 "Triangles": 5h15 print + 5 minutes post-processing
Variant 3 "Airbag": 4h print + 15 minutes post-processing

Variant 3 "Airbag" would be out for me; the shape simply doesn’t work well.
 
Then "I" would, if you are actually considering a webshop :D, offer Variant 1 "curved lines" as standard and Variant 2 "triangles" as a limited special edition, possibly with different lid colours.
If it remains a small series here, Variant 1 & 2 also work.

Regarding Variant 3, I completely agree with you, the shape is not easy to represent nicely on the small surface.
 
Then I’ll unofficially / officially register myself as one of the buyers for the limited special edition V2 "Triangles" with Cupra logo :D

@Milan
I could almost set up a standing order soon :cool:
 
@Milan

But you only have yourself to blame if you keep coming out with cool new stuff :D
 
Yep, I’m curious to see what comes out of it :P
 
Mehr Dreiecke? Mehr Dreiecke!

Version 4 - "Durcheinander":
IMG_0035.jpgIMG_0036.jpg

Ich habe jetzt alle (sinnvollen) Versionen der Deckel fertig "konstruiert". Die Idee mit dem Müllbeutel habe ich verworfen. Das Volumen des Bechers (ca 180ml) ist einfach nicht ausreichend groß und wäre durch die Arretierungsvorichtung und überschüssige Mülltüte einfach mal fast schon halb verbraucht.
 
OK. Ich "like" das trotzdem! Ich glaube, die erste Dreiecksvariante wäre mein Favorit.
 
Das Paket vom @Milan kam heute an.
Sehr gut verpackt, werde noch Praxis Bilder machen wie es aussieht, aufjedenfall bin ich sehr stark von den Regenschirmhaltern begeistert, diese halten Bombenfest.
Der Toröffner der umgebaut wurde überzeugt in der Optik stark und funktioniert einwandfrei.

Bilder folgen, man kann hier keine Bilder hochladen die nh gute Qualität haben
 

* = Advertisement
Links marked with an asterisk (*) are affiliate links. If you click on one of these links and make a purchase, we receive a commission from the respective online shop or provider. This does not affect the price you pay.

cupra.forum · Alle Rechte vorbehalten · Dies ist kein Forum der Seat Cupra S.A.U.
Back
Top