@dtmdriver

Nein passt nicht mehr in die untere Position.
 
I have now ordered the Option Sub blind for my Leon SP and so far I am quite pleased.
Did you use 0° or 180° phase with the Molex adapter? My subwoofer will arrive tomorrow, and so far there is only the Formentor as a video guide for the Sennheiser (here with 0° phase).

However, I have opted for the 4-ohm variant with the larger bass reflex enclosure.

According to information online (feel free to correct me), the original subwoofer for the Sennheiser system is equipped with a dual voice coil of 2×2 ohms (in series), resulting in a total impedance of 4 ohms. The subwoofer advertised by ARS24 also has a dual voice coil with a resistance of 2×2 ohms - however, here it is connected in parallel, resulting in a total impedance of 1 ohm! This is why it is so loud and needs to be significantly reduced in the equalizer...

I personally see this as problematic. Therefore, I will be using the dual voice coil with 2×4 ohms connected in parallel (2 ohms total impedance) before the amplifier gives out.
 
Last edited:
@Angefixt

Dann ist die Reserveradmulde beim
Leon tiefer als beim Formentor.
Bei meinem passt sie definitiv nicht mehr in die untere Position.
 
Entweder das oder die Schienen für den Ladeboden sitzen höher. Kannst ja mal büdde die Werte angeben zum Vergleich.
 
@dantheman die Reserveradmulde ist beim Formentor ist deutlich flacher als beim Leon.

Hierbei handelt es sich ja auch nur um einen Styropor-Rahmen über einer minimalen Mulde.
 

Attachments

  • 20260521_200213(1).jpg
    20260521_200213(1).jpg
    338.8 KB · Views: 17
  • 20260522_053410.jpg
    20260522_053410.jpg
    622.5 KB · Views: 17
Last edited:
@Cuprabea very cool. Definitely a good decision...

I would find it interesting to hear the difference, as I consciously chose the other model. 2×4 Ohm (instead of 2×2 Ohm) impedance with ferrite magnet (instead of neodymium magnet).

How did you set up the system? My settings are as follows:

Subwoofer:
0° phase

Studio:
Music Immersion 3/4

Equalizer:
Subwoofer +3 Bass 125Hz 0 Low Mid 500Hz -1 Mid 1kHz -1 High Mid 5kHz +1 High 10kHz +1

Sound Focus:
Mittig
 

Attachments

  • OPTION Drive10BR-P (2x4 Ohm) vorher_nachher.jpg
    OPTION Drive10BR-P (2x4 Ohm) vorher_nachher.jpg
    2.1 MB · Views: 23
I also initially thought of taking the one you mentioned, but I have no experience at all and contacted ARS24.
They said that sound-wise the drive 10 flat fits better with the Sennheiser.
I still need to try the settings for a few days.
I will add them later.
It would really be interesting to see how the two subwoofers differ.
 
He said that sound-wise the drive 10 flat fits better with the Sennheiser.
The interesting thing is that they can’t actually specify what the real differences are.

The statement that it "fits better" was personally too vague for me.
Because both the smaller sound chamber and the more fragile magnet are clear drawbacks in my view.

Added to that is the higher load on the amplifier due to the lower impedance.

It undoubtedly has more power (about +3dB), but it also draws significantly more current. However, the power is irrelevant if you don’t even turn the subwoofer up fully, but instead set it into the negative range of the equaliser.

My assessment is based 100% on technical facts and the conclusions I draw from them – so a listening test would be really interesting.
 
Your statement is very interesting
I can't comment on that and have no knowledge about it.
In the end, I can only say that it sounds significantly better than the original.
 
Since I am currently riding my motorcycle more and wasn't so sure about the settings, I'm only sharing my settings with you today. Pictures

What I noticed over the weekend is that when the system starts up (when opening the door), the subwoofer thumps three times.
I contacted ARS 24 today and asked if that was normal.
The response:
That is normal, as the subwoofer receives lower frequencies than the original.

The thumping has basically always been there; the original subwoofer just couldn't receive and output the tones or frequencies.
 

Attachments

  • 20260527_162047.jpg
    20260527_162047.jpg
    879.6 KB · Views: 29
  • 20260527_162138.jpg
    20260527_162138.jpg
    719.7 KB · Views: 29

* = Advertisement
Links marked with an asterisk (*) are affiliate links. If you click on one of these links and make a purchase, we receive a commission from the respective online shop or provider. This does not affect the price you pay.

Back
Top