Brake judder at 130 km/h

Welcome! You have been invited by Gand-Alf to join our community. Please click here to register.

PH!L93

War schon mal da
Dear CUPRA Community

I need your experience with my Cupra Leon VZ. The car is only three months old, has run 4,300 km, and was properly broken in during the first 500 km. Since a highway braking from about 220 km/h, I have the following problem:

A steering wheel vibration when braking from 140 to 100 km/h with light pedal pressure. The harder the DCC chassis is set (Sport/Cupra mode), the more unfiltered it comes through in the steering wheel.
  • In dry conditions: The vibration is clearly noticeable. The perforated discs at the front show slight thermal discoloration (bluish), but are visually mirror-smooth.
  • In wet conditions/rain: Absolutely nothing! The brake behaves completely calmly, smoothly, and unobtrusively in wet conditions.
My questions to you:
  1. Does anyone know this phenomenon where the drilled brake only vibrates when dry and is completely quiet in wet conditions (water film as a lubricant/damper?)? Is this the typical cementite formation?
  2. What are the warranty chances with Cupra for thermal distortion at this vehicle age and under 10,000 km despite the slight discoloration?
  3. Has anyone here ever had their windows replaced under warranty, and did the problem come back afterwards?
I will send you some more pictures of the brakes. From my perspective, the ones at the back are in new condition. If more photos would be helpful, let me know.

Thank you for your tips and experiences!
 

Attachments

  • IMG_3724.jpeg
    IMG_3724.jpeg
    1.3 MB · Views: 25
  • IMG_3723.jpeg
    IMG_3723.jpeg
    2.1 MB · Views: 24
  • IMG_3722.jpeg
    IMG_3722.jpeg
    1.2 MB · Views: 25
  • IMG_3721.jpeg
    IMG_3721.jpeg
    2.1 MB · Views: 26
It's best to go to the workshop and describe the problem including the trigger. If there is something wrong with the brake, it should also be addressed under warranty. If the permissible top speed is over 220 km/h, then the brake must be able to withstand something like that.
 
If the permissible maximum speed is over 220 km/h, then the brake must withstand something like that.

If the problem is even related to that. I can hardly imagine it. During tests, we perform numerous full stops from such speeds, and there have never been any abnormalities afterwards.
 
I believe that the cause may be found elsewhere than in a single braking from high speed on the highway.
 
Thank you for the input. I will bring it up at the workshop. In which direction do you think it could go?
 
It's hard to assess that from a distance. However, I would definitely show it to the workshop. They should take a close look at the entire braking system.
 
If the problem is even related to that. I can hardly imagine it. During tests, we perform numerous full stops from such speeds, and there have never been any irregularities afterwards.
Yes, of course. With a fault-free brake, nothing should happen, that was the intention. 😉
 
As mentioned: Off to the workshop.
 
Hello,
I also have a jerking/fluttering in the steering wheel when braking. Brake pads + discs are new, and I also changed the wheel set. The problem is still there... I can't find the error :(
 
It occurs more strongly at lower speeds than at higher ones. Sometimes it is stronger, sometimes weaker. I often notice it when approaching a traffic light at around 50-60 and then braking down from 20-10; it is very strong then. Well, after the replacement, just break it in normally, no sudden braking, etc. The brake was properly broken in.
 
One would need to continue checking, of course, as this is associated with costs since it is no longer under warranty...
 

* = Advertisement
Links marked with an asterisk (*) are affiliate links. If you click on one of these links and make a purchase, we receive a commission from the respective online shop or provider. This does not affect the price you pay.

Back
Top